Dolby Laboratories CP650 Installation Manual Page 129
- Page / 184
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Dolby
®
Model CP650 Installation Manual Maintenance and Troubleshooting
9-7
9.3.2 Exploded View and Board Locations
Cat. No. 773
Dolby Digital Decoder
Cat. No. 790
Dolby Digital Surround EX
Decoder / Digital Aux. Input Card
Cat. No. 778
Dolby Digital Surround EX
Decoder / Digital I/O Card
Bypass
Mains Voltage
Selector Switch
(110/220 VAC)
Front Panel
Mounting Screw
Front Sub-Panel
Mounting Screws (7)
Front Sub-Panel
Cat. No. 792
Bypass Power Regulator
Bypass Power Supply
Fuse Holder 5 X 20 MM
110 VAC: T 200 mA L
220 VAC: T 100 mA L
Power / Bypass
Button
Cat. No. 774A
System Controller
Cat. No. 772A
Analog I/O and Bypass
Cat. No. 776
Power Supply
Assembly
-or-
Cat. No. 791
Digital Crossover Card
(for use with Cat. No. 790 only)
FB425C04.CDR
Figure 9–10 Model CP650 Exploded View
Caution: Many components used on the circuit boards are sensitive to electrostatic damage.
It is essential to wear an earthing strap while handling or changing CP650 circuit boards.
To gain access to the CP650 circuit boards:
1. Remove the AC mains power cable.
2. Open the setup control-panel access door.
3. Remove the front-panel mounting screw located in the upper right-hand corner of
the setup control panel and carefully pull the front-panel toward you to remove it.
4. Remove the seven front subpanel mounting screws, and carefully pull the
subpanel toward you to remove it.
5. Unplug the two ribbon cables connected to the internal circuit boards.
The power supply assembly can be removed by loosening the two finger screws on
the front edge of the assembly and the two rear-panel screws above and below the AC
mains connector. From the front of the unit, carefully remove the connector at the
backplane along with the two front connectors, then slide the assembly out.
- Model CP650 1
- Installation Manual 1
- Dolby Laboratories, Inc 2
- Table of Contents 3
- List of Figures 7
- List of Tables 9
- Chapter 1 13
- Introduction 13
- 1.3 Accessories 15
- 1.5 Specifications 15
- Dolby Digital 19
- Surround EX mode 19
- 1.9 Regulatory Notices 22
- 1.9.5 Notices for Europe 23
- Chapter 2 25
- Installation 25
- 2.3 Mount the CP650 27
- 2.5 Connect the CP650 28
- 2.5.2 Remote Controls 29
- 2.5.5 Digital Audio Sources 32
- OPTION CARD I/O 33
- (See Section 9.3.2.) 36
- PROFESSIONAL AUDIO 37
- EQUIPMENT 4J06 37
- CP650 INSTALLATION WIRING 38
- AUDIO OUTPUT CONNECTIONS 38
- FLOW CHART 41
- CP650 SYSTEM 41
- Chapter 3 43
- 3 1/3 db 46
- Chapter 4 53
- B-Chain Alignment 53
- 4.2 Microphone Placement 54
- 4.3 Initial Setup 55
- 4.5.1 Main Channels 58
- 4.5.2 Subwoofer Channel 60
- Cat. No. 791 61
- Screen Loss 61
- Filter Jumpers 61
- Setting Corner Frequency 65
- Next Channel 68
- Crossover Levels screen 69
- 1, 2, 4 kHz 72
- = Flat 73
- = EQ Assist 73
- 4.7.4 The EQ Assist Feature 74
- Saving Changes 76
- Chapter 5 81
- A-Chain Alignment 81
- 5.4 Dolby Level Set 84
- O O 85
- O O 85
- 5.6 Cell Alignment Check 87
- 5.7 Cell Wiring Check 88
- 5.8 Azimuth Check 88
- 5.9 Focus Check 89
- Chapter 6 93
- Digital Soundheads 93
- 6.3 Focus Adjustment 94
- Chapter 7 97
- Final Adjustments 97
- Width (feet) 100
- Width (meters) 101
- 7.5 Nonsync Level Adjustment 103
- < + > 104
- 105
- 7.11 Reversion Mode 108
- 7.13 Noise Gating 109
- 7.14.1 Operation 110
- • Auditorium unoccupied 110
- • Doors closed 110
- 7.14.4 “FAIL” Parameters 113
- 7.16 Clock Set 115
- 7.17 Date Set 116
- Chapter 8 117
- Accessories 117
- 8.2.1 Remove the Housing 118
- Top View 119
- 8.2.5 Assemble the Unit 120
- 8.2.6 Connect to the CP650 121
- Chapter 9 123
- Remove wires 124
- Oscilloscope 125
- Output Adjust 126
- Replacement lamp: 127
- Use only General Electric EPT 127
- Reflector-type 127
- Dolby Part No. 34010 127
- 9.3 CP650 Troubleshooting 128
- FB425C04.CDR 129
- 9.3.3 The Event Log 130
- 9.3.4 Troubleshooting Chart 130
- NO SOUND AT ALL 131
- NO SOUND IN SOME 132
- FORMATS 132
- FADER PROBLEMS 133
- CONTROL PROBLEMS 133
- RUMBLES, WHISTLES 134
- HUM IN SOUND 134
- TROUBLE IN ONE OR 135
- MORE CHANNELS 135
- CHANGEOVER AND 138
- CONTROL TROUBLES 138
- CP650 POWER SUPPLY WIRING 140
- CAT.NO.776-1 (BLACK COVER) 140
- CAT.NO.776-2 (GOLD COVER) 141
- CAT. NO. 701 EXPLODED VIEW 142
- CAT. NO. 700/701 REAR VIEW 143
- Appendix A 145
- Software Operations 145
- A.2 Updating CP650 Software 146
- Appendix B 149
- Back Panel Connectors 149
- * No connection 150
- D-connector 150
- B.2 Input Connectors 152
- Pin Connection 154
- Pin Connection 155
- B.3 I/O Connectors 156
- Appendix C 159
- 123 7456 8 160
- Appendix D 161
- Format Descriptions 161
- D.2 Format Definitions 162
- Cat. No. 778 AES1 171
- Appendix E 173
- External Control of CP650 173
- Commands 174
- Examples 175
- Appendix F 179
- Setup and User Menus 179
- + = 179
- Mutes CP650 if not detecting 181
- F.2 CP650 User Menu 182
- DIP switch 6 DOWN 182
Related products and manuals for Recording Equipment Dolby Laboratories CP650
(36 pages)© 2020, manymanuals.com. All rights reserved. | 1.002 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals