Dolby Laboratories CP500 Specifications Page 14
- Page / 154
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
1-5
1.5 Regulatory Notices
FCC
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with this instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his or her own
expense.
UL
The CP500 is UL listed. This installation manual is for use by qualified personnel only. To avoid
electric shock do not open the unit or perform any servicing unless you are qualified to do so.
WARNING
: Check that the correct fuse has been installed. To reduce the risk of fire, replace the
fuse only with the same type and rating.
FUSE - 2 Amp, time-lag (T2A), 20 mm long, 250 Volt
Dolby part no. 56027
The ground terminal of the power plug is connected directly to the chassis of the unit. For
continued protection against electric shock, a three-pin, correctly wired and earthed power outlet
must be used. Do not use a ground-lifting adapter and never cut the ground pin on the three-prong
plug.
UK
WARNING
: THIS APPARATUS MUST BE EARTHED.
As the colours of the cores in the mains lead may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
• The core that is coloured green and yellow must be connected to the terminal in
the plug that is marked with the letter E or by the earth symbol
or coloured
green or green and yellow.
• The core that is coloured blue must be connected to the terminal that is marked
with the letter N or coloured black.
• The core that is coloured brown must be connected to the terminal that is marked
with the letter L or coloured red.
IEC
This unit complies with the EMC requirements of EN50081-1 and EN 50082-1 when installed in
an E2 environment in accordance with this manual.
- Film-Tech 1
- Model CP500 2
- Model CP500 3
- TABLE OF CONTENTS 4
- 1.1 About the Dolby CP500 10
- 1.3 About This Manual 11
- 1.4 Specifications 12
- 1.5 Regulatory Notices 14
- SECTION 2 16
- EQUIPMENT REQUIRED 16
- TEST FILM 17
- 3.1.2 While playing the film: 18
- 3.2 Mount the CP500 19
- 3.3 Connect the CP500 19
- (Models CP500-D, and -70) 20
- Figure 3 - 2 22
- Figure 3 - 3 22
- 3.4 Check and Set Jumpers 23
- CAT. NO. 683 25
- Appendix B, Cat. No. 683 26
- Model CP500-D 27
- Model CP500-D/300 28
- Model CP500-SR 28
- Model CP500-70 28
- 3.6 Bypass Power Wiring 29
- 3.7 Power On 30
- 4.1 The CP500 Front Panel 32
- 4.2 System Password 35
- 4.3 Aligning the B-Chain 36
- 5.1 Check Theater Equipment 38
- 5.2.2 Screen Channels 39
- B-Chain Alignment 40
- 5.3 Room Equalization 41
- “85 dBC” 44
- Reference 47
- Response 47
- CAT. NO. 682 52
- Cat. No. 682 card 53
- 6.1 Aligning the A-Chain 54
- LAMP VOLTAGE DC ADJUSTMENT 56
- OSCILLOSCOPE TRACES 60
- CAT. NO. 661 61
- P1, Left 62
- 7.1 Mechanical Alignment 66
- 2.7 to 5 volts 67
- Voltage Adjust 68
- 7.6 Optical Alignment 69
- Figure 7- 5 70
- 7.8 Film Threading 71
- 7.9 Cat. No. 673 72
- 7.11 Format Control 72
- Allowable Source Formats 75
- Allowable Target Formats 75
- How It Works 75
- Assigning Source Formats 76
- Assigning Target Formats 77
- Figure 7- 8 78
- 7.13.2 Print Cleanliness 79
- 7.13.3 Adjustments 79
- SECTION 8 80
- FINAL ADJUSTMENTS 80
- 8.2.1 Static 82
- 8.2.2 Dynamic 83
- 8.2.3 Typical Settings 83
- Width (feet) 84
- Width (meters) 84
- 8.4 Bypass Adjustments 85
- Position J900 to 86
- REMEMBER 87
- Format 04 Dolby Stereo 89
- Adjustments 90
- 8.5 About Non-sync 91
- 8.6 Mute Speed Adjustment 92
- Figure 9 - 1 93
- CAT. NO. 689 REMOTE 94
- 9.1.3 Auditorium Fader 95
- 9.2.1 Operation 96
- 9.2.2 Components 98
- 10.1 During the Show 99
- Surround Speakers 101
- Electronic Crossover: 101
- 10.2 Between Shows 102
- WARNING: 104
- 10.3 Troubleshooting Chart 105
- NO SOUND AT ALL 106
- NO SOUND IN SOME 107
- FADER PROBLEMS 108
- CONTROL PROBLEMS 108
- RUMBLES, WHISTLES 109
- HUM etc. IN SOUND 109
- TROUBLE IN ONE OR 110
- MORE CHANNELS 110
- CHANGEOVER AND 113
- CONTROL TROUBLES 113
- APPENDIX A 115
- ADVANCED OPERATIONS 115
- Cancel OK 116
- A.2 Saving System Settings 119
- Saving System Settings 120
- A.2.2 Using Load500 Software 125
- Connect to Load500 127
- Menu Cancel OK 130
- B.1 Description and Features 131
- B.2 Installation 131
- B.3 Alignment 132
- B.4 Special Applications 134
- B.5 Headers Available 135
- B.6 Jumpers and Headers 136
- APPENDIX C 138
- 9. Mic. Input Connector: 140
- System Setup Menu Tree 144
- Signal Block Diagram 144
- Basic Functions 145
- Auxiliary Data Channel 147
- Optical Sound 149
- Magnetic Sound 150
- Dolby Gets Involved 151
- The Next Step: Dolby SR 152
- And Now - Dolby Digital 152
- About Dolby AC-3 153
- Making Films Sound Better 153
Related products and manuals for Recording Equipment Dolby Laboratories CP500
(123 pages)© 2020, manymanuals.com. All rights reserved. | 0.188 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals